The Western Digital Raptor (often marketed as WD Raptor) is a series of high performance hard disk drives produced by Western Digital. The drive currently occupies a niche in the enthusiast, workstation and small-server market. Traditionally, the majority of servers used hard drives featuring a SCSI interface because of their advantages in both performance and reliability over consumer-level ATA drives.
Although pitched as an "enterprise-class drive", it won favour with the PC gaming and enthusiast community because the drive was capable of speeds usually found only on more expensive SCSI drives. Adopting the SATA interface meant that it could be used easily on all modern motherboards with no separate (and often expensive) controller card. Also, integration was made easier still by the inclusion of a standard 4-pin Molex power connector in addition to the standard SATA power port.
Despite having been in production since early 2003, there is no direct competition in the same market.
More recently, Western Digital acknowledged the primary consumer of its Raptor brand drives by releasing a revision of its flagship 150 GB drive. In keeping with the PC case modding trend of stylizing, the drive was given a Perspex window to match the internals of computer cases. This allows the user to see the drive's inner workings while it is in operation.
On April 21, 2008, Western Digital announced the next generation of its 10,000 RPM SATA Raptor hard drive series. The new drives, called WD VelociRaptor, feature 300 GB capacity and 2.5-inch platters enclosed in the IcePack, a 3.5-inch mounting frame with a built-in heat sink. Western Digital claims the new drives are 35 percent faster than the previous generation Raptors.[1]
On April 6, 2010, Western Digital updated the VelociRaptor series. The drives now contain up to three platters and a 600GB total capacity, upgraded from the dual-platter 300GB design of the prior flagship model. Western Digital claims the new models are 15 percent faster than the previous generation VelociRaptors.[2]
Contents |
In 2003, Western Digital released the first incarnation of the Raptor series: the WD360GD.[3] It featured a capacity of 37 GB on a single platter, a Serial ATA interface, and was the first ATA drive to operate at a spindle speed of 10,000 revolutions per minute. Like many early SATA drives, the Raptor was not a "real" SATA drive because it was really a PATA drive that used an 88i8030C interface bridge chip from Marvell. However, this fact did not significantly hamper the Raptor's performance. WD360GD Raptors do not use the 3.3 V Serial ATA power line. There is no need to use a SATA power connector as it will not be fully utilized.[1]
As is usually the case for hard drives featuring a faster spindle speed, the Raptor outperformed other ATA drives and in some situations was even able to reach the performance of contemporary 10,000 rpm SCSI drives. SCSI drives still outperformed the Raptor in multi-user scenarios, but for high-end home computers it fared very well. For enthusiasts' systems, the Raptor also had the key advantages of low noise and temperature levels compared to similarly performing drives.
All WD360GD drives with Part Number WD360GD-00FNA0 (December 2003) and earlier cannot accept SATA latch cables, as the SATA data connector does not have the required rails. So, only normal cables can be plugged into these connectors.
WD360GD Raptors with the Marvell 88i8030-TBC PATA to SATA bridge chip, such as WD360GD-00FNA0 (December 2003) and earlier, are limited to UDMA 5 transfers. In Linux, "applying bridge limits" is displayed and then it allows transfers up to UDMA\100. In Microsoft Windows, they are reported as UDMA 6, but give a burst rate of 104 MB/s, while WD360GD with the 88i8030-TBC1 chip are reported as UDMA 6 and give a burst rate of 122 MB/s, close their theoretical limit of UDMA 6. Those Raptors limited at UDMA 5 were bought for SATA I 150 MB/s support, but they only support the legacy PATA UDMA 5 at 100 MB/s.
Like its larger brother the WD740GD, the WD360GD was revised in 2006 and released with the designation WD360ADFD - incorporating twice as much on-board cache (16 MB vs 8 MB), at least one side of a single platter that offers twice the areal density, and enabling NCQ.
The second generation Raptor was introduced in early 2004, featuring two platters for 74 GB of storage space. Unlike its predecessor, the WD740GD didn't use ball bearings to support the spinning disks, but rather used fluid dynamic bearings. These allowed the new Raptor to operate at a noise level comparable to the quieter 7,200 rpm drives.
Another advantage the WD740GD had over its predecessor was Tagged Command Queuing, a feature that had previously been available only in SCSI drives. Command queuing resulted in a notable increase in the WD740GD's multi-user performance—a key discipline where its predecessor failed compared to SCSI drives. However, enabling command queuing on the WD740GD resulted in a performance decrease in single-user scenarios. It is worth noting that as of 2005[update], only a few SATA controllers can fully support command queuing. This drive became immensely popular in high-end gaming systems because of these features.
In 2006 Western Digital revised the WD740GD specification and released the WD740ADFD, ostensibly the same drive but with 16 MB of on-board cache, and a larger single platter (one 75 GB platter vs two 37 GB platters). Support for TCQ (rarely supported on SATA RAID controllers) was dropped in favor of NCQ, and at the same time replacing the SATA-to-PATA bridge controller chip with a native SATA controller. Unfortunately one of the major enhancements of WD740ADFD, the NCQ, is implemented so badly in the WD740ADFD-00NLR1 that it has been added to the Linux libata drive blacklist. The WD740GD did not apply because it uses TCQ and not NCQ. In order to deal with it, NCQ is disabled Link to the NCQ-Bug in the Kernel Bug Tracker. In TCQ capable controllers, the WD740GD is possibly faster than its successor as some of the WD740ADFDs' gains are lost. The WD740ADFD has also caused problems in some motherboards and their manufacturers had to release BIOS updates.
The third generation Raptor was released by Western Digital in January 2006. It features two 75 GB platters (for a total of 150 GB) and a more advanced system of Native Command Queuing. At the same time, the Raptor X was released. It has identical specifications to the standard Raptor,[4] but it has the addition of a clear polycarbonate window in the drive cover, making the movements of the disks and magnetic heads visible. This unique feature is likely to be popular with case modders. Like the regular Raptor, the Raptor X has a MTBF rating of 1.2 million hours, or 137 years. Both drives are covered by a five-year warranty. While this drive uses the NCQ feature of SATA 2, it lacks support for the increased bandwidth of SATA 2.[5]
The fourth generation Raptor was announced by Western Digital in April 2008. The new drive is being sold under the VelociRaptor name.[6] As well as increasing the capacity to 300 GB (split over two 150 GB platters), the form factor is follows:
Earlier GLFS models have been criticised for being incompatible with 3.5" SATA hot swap bays due to the position of the connectors; however, a new revision (HLFS models) has been released which remedies this problem.[7] Furthermore, TLER has been enabled by default on HLFS models.
Western Digital later released a 2.5 inch Velociraptor (BLFS models) which is nearly identical to the 3.5 inch version, but without the IcePack heat sink. These drives are designed for use in blade servers and are normally unsuitable for laptops because of their power requirements and 15 mm thickness. Of course, TLER is also enabled by default on BLFS models.
A severe issue with the 4th generation of raptor drives was faulty firmware, which caused the drive to report TLER timeouts after roughly 50 days of continuous usage (precisely: 49.71 days counted in milliseconds, which corresponds to overflow of a 32bit number)[8][9][10]. The bug has been present in all models of the shipped drives - from their introduction up to late 2009. WDC has never admitted the existence of the bug, or officially released the firmware update. The firmware was leaked by WDC technician and is still easily available through upload sites[11]). The bug was of minor issue for desktop users, but prolonged usage in raid setups could result in mass drive dropouts after mentioned 49.71 days causing maintenance problems and potential data loss.
The fifth generation Raptor (or 2nd generation VelociRaptor) drive was announced in April 2010. Besides increasing the total capacity to 600 GB, the SATA interface speed had been increased to 6 Gbit/s. The drives are sold either in the same IcePak mounting frame as the previous generation, or as bare drives (intended for blade servers). While the drive width of 2.5" may entice users to try to install a VelociRaptor drive in a laptop, this is not possible. Not only are the drives a thicker-than-usual 15mm high, but they require both +12V and +5V power that most laptops cannot provide. Standard laptop hard drives typically only require +5V.
| Model no. | Gen. | Released | Capacity | Cache | Interface | Feature set | Notes | Product Page |
|---|---|---|---|---|---|---|---|---|
| WD360GD | 1 | 2003 | 36 GB | 8 MB | Parallel ATA to Serial ATA bridge | – | – | Specifications |
| WD740GD | 2 | 2004 | 74 GB | 8 MB | Parallel ATA to Serial ATA bridge | TCQ | – | |
| WD360ADFD | 3 | 2006 | 36 GB | 16 MB | Native SATA | NCQ | – | |
| WD740ADFD | 3 | 2006 | 74 GB | 16 MB | Native SATA | NCQ | – | |
| WD1500ADFD | 3 | 2006 | 150 GB | 16 MB | Native SATA | NCQ | – | Specifications |
| WD1500AHFD | 3 | 2006 | 150 GB | 16 MB | Native SATA | NCQ | Raptor X variant | Specifications |
| WD740HLFS | 4 | 2008 | 74 GB | 16 MB | Native SATA 3 Gbit/s | NCQ | VelociRaptor | TBA |
| WD1500BLFS | 4 | 2008 | 150 GB | 16 MB | Native SATA 3 Gbit/s | NCQ | VelociRaptor | Official site |
| WD1500HLFS | 4 | 2008 | 150 GB | 16 MB | Native SATA 3 Gbit/s | NCQ | VelociRaptor | Official site |
| WD3000BLFS | 4 | 2008 | 300 GB | 16 MB | Native SATA 3 Gbit/s | NCQ | VelociRaptor | Official site |
| WD3000GLFS | 4 | 2008 | 300 GB | 16 MB | Native SATA 3 Gbit/s | NCQ | VelociRaptor | Official site |
| WD3000HLFS | 4 | 2008 | 300 GB | 16 MB | Native SATA 3 Gbit/s | NCQ | VelociRaptor | Official site |
| WD4500BLHX | 5 | 2010 | 450 GB | 32 MB | Native SATA 6 Gbit/s | NCQ | VelociRaptor | Official site |
| WD4500HLHX | 5 | 2010 | 450 GB | 32 MB | Native SATA 6 Gbit/s | NCQ | VelociRaptor | Official site |
| WD6000BLHX | 5 | 2010 | 600 GB | 32 MB | Native SATA 6 Gbit/s | NCQ | VelociRaptor | Official site |
| WD6000HLHX | 5 | 2010 | 600 GB | 32 MB | Native SATA 6 Gbit/s | NCQ | VelociRaptor | Official site |
| WD1500HLHX | 5 | 2011 | 150 GB | 32 MB | Native SATA 6 Gbit/s | NCQ | VelociRaptor | Official site |
| WD3000HLHX | 5 | 2011 | 300 GB | 32 MB | Native SATA 6 Gbit/s | NCQ | VelociRaptor | Official site |
| Special models | ||||||||
| WD800GD | 2 | 2004 | 80 GB | 8 MB | Parallel ATA to Serial ATA bridge | TCQ | – | |
| WD800ADFD | 3 | 2006 | 80 GB | 16 MB | Native SATA | NCQ | Initially HP/Dell-exclusive; now retailed | Official site |
| WD800ADFS | 3 | 2006 | 80 GB | 16 MB | Native SATA 3 Gbit/s | NCQ | Initially HP/Dell-exclusive; now retailed | Official site |
| WD1600ADFS | 3 | 2006 | 160 GB | 16 MB | Native SATA 3 Gbit/s | NCQ | Initially HP/Dell-exclusive; now retailed | Official site |
| WD800HLFS | 4 | 2008 | 80 GB | 16 MB | Native SATA 3 Gbit/s | NCQ | Initially HP/Dell-exclusive; now retailed | Official site |
| WD1600HLFS | 4 | 2008 | 160 GB | 16 MB | Native SATA 3 Gbit/s | NCQ | HP/Dell-exclusive | Official site |
Official
Reviews